Page 2 of 3 FirstFirst 123 LastLast
Results 11 to 20 of 21
Like Tree1Likes

Thread: CAR won't run for more then 3-5 secs.. Fuel Injector cleaning?

  1. #11
    Neutrino MadMaxAtom's Avatar
    Join Date
    Apr 2011
    Location
    Usually in my shop..
    Posts
    1,583
    Country
    United States
    Try jumping the fuel pump relay out.The pump should run, and take a pressure reading.If pressure is ok,and you are losing the fuel pressure when it dies,you are losing the run signal to the pump relay.

    Try running the engine with the relay jumped (it won't hurt anything) if it still doesn't run,you may have lost your ignition reference signal.(unplugged,bad sensor etc)
    The power of an Atom is a terrible thing to waste! Atom owner/operator since 2007. The more you chase perfection,the faster it becomes. John Force for President! (I asked him once in person...he laughed)

  2. #12
    Lepton Positron's Avatar
    Join Date
    May 2011
    Location
    SoCal
    Posts
    358
    Country
    United States
    Quote Originally Posted by ksrimounchanh View Post
    so, those are the suppose to be expected per all the info I have read. I did find something od..

    hooked up a fuel pressure gauge on the fuel rail and even though it was squirting out, the pressure was way low..

    Looks like I am going to open up the fuel pump again.

    KS..

    will keep you all posted.
    What was the fuel rail pressure when you read with gauge? should be over 50psi. General convention is that squirting out is bad, I assume this is to anecdotal test for presence of fuel rather than not.

    Did you change gasket as a matter of course or contamination? Is tank less than 1/2?

    My beer says sock on bottom of bucket plugged with black bits from gasket. If under 1/2 tank the bucket has no way to fill if sock plugged. No pressure, no go.

    Pain to check but easier than pulling pump, if you changed sock on fuel pump when you R&R'd the pump, put more than 1/2 tank and retest. If level over slosh bucket pump will be submersed and pressure should return. Easy to drain tank by unplugging fuel hose from fuel rail into fuel can, also a way to see if pump making volume.

    Always a good idea to have someone there with a fire extinguisher at the ready when spraying gas all over the place..
    AtomII #73 for sale, PM for details.

    Turning money into smoke and noise since 2006.
    Member "I drove the Brammo mule with Tom S." club.


  3. #13
    Fermion
    Join Date
    Jun 2011
    Location
    Kansas City, KS
    Posts
    66
    Country
    United States
    the pressure on the rail was below 10psi. I took the pump back out prior to reading above. I notice the plastic piece that is attached to the top piece was actually not fully attached to the top cover, it was on there because of the little space it had to move around.

    Not sure the name.. but as I pulled the pump out, I notice it was just wobbling. I wish I would have taking note but that is what I notice once I got it out. There is a slight chance, I could have pulled it out when I lifted the pump from the tank.

    pump.jpg


    the inside sock was still clean.. the bottom was already looking much darker and dirtier.. is this normal or should it be better.

    bottom-sock.jpg

    The gasket also looks a bit worn already... These were only on for last fall.. Around the time Terry picked up his car and did another cross-country.

    gasket.jpg

    looks like I should just replace all?

    Good thing several folks here suggested threaded rivet for the firewall for easier. Didn't think I would need back in so darn soon.

    KS

  4. #14
    Proton Terry Kennedy's Avatar
    Join Date
    Aug 2010
    Location
    NYC
    Posts
    796
    Country
    United States
    Quote Originally Posted by ksrimounchanh View Post
    the inside sock was still clean.. the bottom was already looking much darker and dirtier.. is this normal or should it be better.
    I've seen worse. Remember, you originally thought you had an overheating problem as your car would run for 20 minutes or so, and your original filter sock was probably a lot worse than that.

    The gasket also looks a bit worn already... These were only on for last fall.. Around the time Terry picked up his car and did another cross-country.
    Did you replace both gaskets (fuel pump and filler neck) when you changed the pump? Where did you get the gaskets? The gasket in your picture looks like it is having the same degradation as the original Brammo ones.

  5. #15
    Fermion
    Join Date
    Jun 2011
    Location
    Kansas City, KS
    Posts
    66
    Country
    United States
    Interesting, I did replace the gasket at the same time. I am sure, I recall, mentioning the gasket issue to Sheila and wanted a replacement that will not do the same.

    My original was so bad, I did not have it to compare with the one that Sheila @ TMI sent to me.

    Anyway, off to looking for a new part. Wonder if I actually should ask for a "good gasket" instead of just "gasket" next time. Back to the garage..



    KS

  6. #16
    Neutron
    Join Date
    Aug 2010
    Posts
    2,677
    Country
    United States
    Get a cork based one or make one yourself out of that gasket stuff - what is it - Viton?

    Yes, Viton
    http://www.mcmaster.com/#86075k22/=gnfc2t

    Cuts really easy so you could lay the old one on it and trace out the new one and cut it with scissors or an xacto.


    Here are the cork based ones.
    I dont remember what size you want but any of these should be safe to use as well

    http://www.fuelsafe.com/store/gaskets.html

  7. #17
    Fermion
    Join Date
    Jun 2011
    Location
    Kansas City, KS
    Posts
    66
    Country
    United States
    Lucky, last year, I did not throw away the one I made.. put the pump back in after some cleaning.. made sure all the hose was on, and put it all back.

    This time, when I turn the key on, the PSI on the rail was just a tad bit above 50psi.. wahoo.. hit the start button and it started first time.

    whew...

    now, putting everything back..

    Thank everyone for inputs..

    KS

  8. #18
    Neutron
    Join Date
    Aug 2010
    Posts
    2,677
    Country
    United States
    Awesome. Pulling the fuel pump is one of the most pain in the butt things to do. Sorry you had to do it twice. But oh so satisfying to do it yourself. You would have paid a mechanic what? $800-1000 to do that?

  9. #19
    Neutrino MadMaxAtom's Avatar
    Join Date
    Apr 2011
    Location
    Usually in my shop..
    Posts
    1,583
    Country
    United States
    ^C'mon Bolus..we are not doctors! Unless it would take 12 hrs to R&R the pump,the bill would be nowhere near that, at a respectable repair facility. I can do that job in under two hrs..with a coffee break included...
    The power of an Atom is a terrible thing to waste! Atom owner/operator since 2007. The more you chase perfection,the faster it becomes. John Force for President! (I asked him once in person...he laughed)

  10. #20
    Neutron
    Join Date
    Aug 2010
    Posts
    2,677
    Country
    United States
    Haha, well, I made an estimate based on the fact that BMW wanted to charge me $1200 plus $300 in parts for a front brake pad replacement for my Mini. And since I did it myself in the driveway and it only took an hour I assumed $1200 / hour shop rate.

    Seriously though, if he took the car to like a chevy dealer, said they fuel pump assembly needs to be checked and you have to take out the seats, remove the rear firewall, pull out and fix the pump assembly, check socks and filters,etc. How much would they charge? I thought I was being conservative with my estimate.

    By the way, you have 3 Atom's and I have one that I had to finance. So no more pot comparisons Mr Kettle

Page 2 of 3 FirstFirst 123 LastLast

Similar Threads

  1. Fuel gauge weirdness
    By FrankRizzo in forum US Ariel Atom 2 (Brammo) Technical Discussion
    Replies: 21
    Last Post: August 14, 2011, 08:44 PM
  2. FYI - How much HP the AA3 fuel system can take
    By Payne in forum General Ariel Atom Discussion (for all UK and US versions)
    Replies: 2
    Last Post: May 4, 2011, 10:34 AM
  3. Ariel Atom 2 Injector Harness Pin Outs
    By Steve in forum Documentation Library
    Replies: 0
    Last Post: April 25, 2011, 09:16 PM
  4. Replies: 0
    Last Post: April 25, 2011, 09:04 PM
  5. What are the specs of this fuel injector?
    By Gage in forum GM Ecotec LSJ Engine Technical Discussion
    Replies: 5
    Last Post: February 22, 2011, 10:19 AM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •