Page 1 of 2 12 LastLast
Results 1 to 10 of 15

Thread: wheel bearings/hubs on SRA

  1. #1
    Electron
    Join Date
    Jun 2013
    Location
    DFW
    Posts
    134
    Country
    United States

    wheel bearings/hubs on SRA

    I've heard of folks experiencing wheel bearing failures over time (sooner if running wider/stickier rubber).

    With that said, if one wanted to get ahead of any failures, do you just buy replacement bearings and that's it? Or is replacing the hub assembly in its entirety recommended?

    On a somewhat related note, given that our bolt pattern is 4x100 (at least on the SRA, not sure about the street Atom3 variants), would something like these billet Enduro Miata hubs be a drop-in replacement https://www.miatahubs.com?

  2. #2
    Electron
    Join Date
    Nov 2017
    Location
    Pennsylvania
    Posts
    113
    Country
    United States
    I'd be interested to hear if anyone knows differently but from what research I've done and info I've heard the hubs are proprietary. The miata hubs will not work. Yes you can replace the wheel bearing - if you catch a failure early enough to prevent damage to the hub. I didn't and as a result have had to replace left rear hub and bearing twice - once due to not catching early enough, second due to over-tightening and cracking the hub...sigh. Replacing the bearing requires a press.

  3. #3
    Electron
    Join Date
    Jun 2013
    Location
    DFW
    Posts
    134
    Country
    United States
    @argonaut - do you recall what replacement hub assemblies cost you?

  4. #4
    Positron cvjoint's Avatar
    Join Date
    Mar 2017
    Location
    San Francisco
    Posts
    533
    Country
    United States
    I got the bearing info if anyone needs it. Mine has done over 5,000 miles of pure track time on the originals with no play. I replaced the rears eventually just to be safe but there was no sign of needing it. Yes, you press them out.

  5. #5
    Electron
    Join Date
    Nov 2017
    Location
    Pennsylvania
    Posts
    113
    Country
    United States
    The cost of new rear hub from TMI is ~$230. The bearing is around $84 from TMI (~$30 on the aftermarket...its a standard bearing). Axle nut is about $9. The clip that holds the bearing in the hub is $22.

  6. #6
    Electron
    Join Date
    Jun 2013
    Location
    DFW
    Posts
    134
    Country
    United States
    Well, today I cracked 3K miles on my SRA. Unfortunately, Lady Luck also ran out on me today with an issue on the RR corner, thankfully right as i was pulling into the pits because i felt something funny. I believe it is either wheel bearing failure, or a hub assembly failure. I'm hoping those of you who have experienced these issues can point me in the right direction. I unfortunately had to go home immediately after the incident, so have not had a chance to start disassembling.

    Long story short, I am unable to move the car on its own power. When I put it in gear and give it gas, the car doesn't move. When the car is being towed, there is a scraping sound, and a periodic clicking sound from the RR.

    This is a video of the car with the rear jacked up (both rear wheels in air):
    https://photos.app.goo.gl/v3rbuYM2WSdJjbpaA

    As you can see, the half shaft doesn't rotate with the RR wheel, and obviously the RR wheel is just dangling with TONS of play. The studs are still firmly attached to the hub/brake rotors.

    With the car on the ground, if you push the car forward, the driver's side halfshaft (?) rotates with the LR wheel, but the passenger's side halfshaft rotates opposite of the RR wheel rotation.

    Anyone know from experience if this requires a complete new rear hub as posted above in this thread, or if it's likely just bearings needing replacement?

    What should I be doing in the future from a Preventative Maintenance standpoint to avoid this (proactively replace wheel bearings every year? replace hub assemblies every year?), or is this just a fact of life for tracked Atoms? FWIW, mine is an SRA, track-only. I've done exactly 3K track miles in the last 14 months since purchased new.

  7. #7
    Electron
    Join Date
    Nov 2017
    Location
    Pennsylvania
    Posts
    113
    Country
    United States
    Looks like total hub failure. That happened to me once in a Corvette - wheel only held on by rotor in the brake caliper.

    Preventive - torque to proper spec before every session. DO NOT over torque it, it will crack the hub. Likely the best solution is to pony up for the Palatov 5-lug conversion uprights and then use real, racing quality hubs.

  8. #8
    Electron
    Join Date
    Jun 2013
    Location
    DFW
    Posts
    134
    Country
    United States
    Thanks Argonaut. I do torque the axle nuts to spec (140 front, 180 rear) at the beginning of every track day.

    Do you think replacing the bearings proactively would have been likely to prevent this failure?

  9. #9
    Electron
    Join Date
    Nov 2017
    Location
    Pennsylvania
    Posts
    113
    Country
    United States
    Quote Originally Posted by texevora View Post
    Thanks Argonaut. I do torque the axle nuts to spec (140 front, 180 rear) at the beginning of every track day.

    Do you think replacing the bearings proactively would have been likely to prevent this failure?
    Who can say. Usually you can tell when a bearing starts to go bad, long before failure (do the old 9 and 3, 12 and 6 test). In your case, the hub looks to have failed - if the bearing had gone bad I would have expected you to feel it long before the hub failed. So many people have had rear hub/bearing issues that I've come to the opinion that they really aren't up to the serious abuse dished out on track and should be thought of as wear items (just like pads, rotors and tires). Unfortunately there are no reasonably priced alternatives. I also think the upright/spindle itself is suspect. The machined cup that the bearing is pressed into seems to be made from pretty mild steel and starts to elongate over time. I know mine are slightly out of round. If they ever get bad enough to require replacement I'll be on the phone to Palatov.

  10. #10
    Electron
    Join Date
    Jun 2013
    Location
    DFW
    Posts
    134
    Country
    United States
    Helpful info, thanks.

    Really wish the Palatov uprights weren't so pricey.

    Any chance you know if they are a drop-in replacement on the SRA? (ie doesn't affect suspension geometry)?

Page 1 of 2 12 LastLast

Similar Threads

  1. Extra-long shank suspension rod end bearings for alignment adjustment thimbles
    By sector: 4 in forum Parts and Accessories for Sale
    Replies: 0
    Last Post: November 19, 2017, 03:01 PM
  2. SRA Wheel Questions
    By ElliotCanada in forum Track Discussion
    Replies: 14
    Last Post: October 22, 2017, 06:49 PM
  3. Added the vorshlag bearings to the springs plus another change
    By silver in forum US Ariel Atom 2 (Brammo) Technical Discussion
    Replies: 4
    Last Post: May 8, 2011, 04:52 PM
  4. Hubs?
    By bolus in forum US Ariel Atom 2 (Brammo) Technical Discussion
    Replies: 9
    Last Post: December 28, 2010, 07:38 PM
  5. Shock thrust bearings to reduce stiction
    By bolus in forum Build Projects
    Replies: 6
    Last Post: October 24, 2010, 09:07 PM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •