Page 2 of 2 FirstFirst 12
Results 11 to 17 of 17

Thread: Normal Vacuum reading

  1. #11
    Electron
    Join Date
    Nov 2013
    Posts
    132
    Blog Entries
    1
    Country
    United States
    OK, good point Max, I will not rule that out just yet then.

    The reason I am convinced it is a vacuum leak, basically, i am trying to prove it's NOT a vacuum leak, and work my way backwards

    1. It's displaying a lower than expected vacuum amount on the boost controller
    2. The CRV flutters below 6psi throttle lifts (so going from 6psi to vacuum, basically not enough vacuum to pull on the CRV valve hard enough to let the air escape from the compressor)
    3. This is the normal CRV spring, they don't make a lighter one, just a stiffer one- I ordered that and it arrived today, I'll try that but it sounds like backwards progress to even install that, the problem is the current spring is stiffer than the vacuum applied at relief from lower power levels, or that is the hypothesis at least
    4. when I spray starter fluid around the maze of vacuum lines, it raises the idle temporarily
    5. when I disconnect the MAP sensor for the boost controller (basically FORCING a vacuum leak) a whistling noise in the throttle body area goes away, when I plug the MAP sensor back up, it comes back...

    I'm currently rigging up a vacuum cleaner/leaf blower to pressurized the intake and I'm going to try to apply some cigar smoke to it to see if I can get any leaks to show

  2. #12
    Electron
    Join Date
    Nov 2013
    Posts
    132
    Blog Entries
    1
    Country
    United States
    well that seems impossible, the throttle plates stay closed because this is a fly-by-wire car, any idea how to trick that to get them to open?

    i am seeing a small amount of positive pressure out of a vacuum line i pulled with my test, but not enough to smoke out of holes i don't think

  3. #13
    Lepton
    Join Date
    Oct 2010
    Location
    Portland Oregon area
    Posts
    304
    Country
    United States
    I blame the previous owner.

  4. #14
    Neutrino MadMaxAtom's Avatar
    Join Date
    Apr 2011
    Location
    Usually in my shop..
    Posts
    1,583
    Country
    United States
    "a whistling noise in the throttle body area" Shortly after I purchased my first Atom2 (Max) I discovered a 3/16" port on the throttle body that was open and should have been plugged.The car had a stumble just off idle on acceleration and was slow to come back to curb idle. I plugged the leak and all was well.
    The power of an Atom is a terrible thing to waste! Atom owner/operator since 2007. The more you chase perfection,the faster it becomes. John Force for President! (I asked him once in person...he laughed)

  5. #15
    Electron
    Join Date
    Nov 2013
    Posts
    132
    Blog Entries
    1
    Country
    United States
    so I have found the leak, there is a vent hole in the manual boost controller that is tied to the supercharger, it seems to be by design

    if i plug the hole with my finger, the vacuum jumps to -9.5psi and the idle is a bit better. The question is, why would the hole be there? i am seriously contemplating using some RTV silicone to plug it

    I can't get in touch with DDMworks to ask their input, they are at an event with poor cell coverage.

  6. #16
    Electron
    Join Date
    Nov 2013
    Posts
    132
    Blog Entries
    1
    Country
    United States
    I think what I need to do is give the CRV/BOV a dedicated vacuum line to the intake manifold, and not "T" it into the lines going to this MBC

    here's a cutaway of the MBC, the vent hole is at the top, it seems deliberate so i won't monkey with it

    http://vibrantperformance.com/2012_c...logue_pg26.pdf

    the real question is, where are the vacuum line sources on an ecotec 2.0L for an alternate source? i will start googling
    Last edited by bkthomps; June 20, 2014 at 04:47 PM.

  7. #17
    Electron
    Join Date
    Nov 2013
    Posts
    132
    Blog Entries
    1
    Country
    United States
    update on this, replaced the manual boost controller used to control the supercharger with a non bleed type (hall man) and my vacuum is back to normal levels- thx to all that replied

Page 2 of 2 FirstFirst 12

Similar Threads

  1. Need help reading a schematic
    By silver in forum Humor and Off-Topic Discussion
    Replies: 10
    Last Post: June 20, 2011, 07:45 PM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •